Nghệ thuật xếp hình Nhật Bản: ROSE
Nghệ thuật xếp hình Nhật bản: ROSE. Tài liệu rất có ích, nó giúp bạn nâng cao kỹ năng gấp tất cả mọi thứ bằng giấy. Bạn có thể gấp thành thạo những gì bạn thích cho riêng mình và cho bạn bè bạn.
Kawasaki Rose
6
1
Unfold steps 1 to 4
and this is the
result.
7
Folding the rose begins with creating a grid on the
paper at a 22.5 degree angle, 45 degree/2.
Crease diagonals, and with the coloured side up,
valley fold left side to the diagonal. Repeat above. It
is important to fold the correct side to the diagonal, as
shown in the diagram.
2
Rotate 90
degrees and
repeat steps 1 to
Mountain fold only the bottom layer 4
8
3
Valley fold the tip of the front layer so that it is
flush with the layer behind. Repeat behind.
4
Valley fold/unfold first two layers of paper. Repeat
behind
Unfold and you should
now have a grid on a
22.5 degree angle.
5
Valley fold/unfold first four layers of paper. I
recommend that the folder fold at most two layers of
paper at a a time to avoid paper drift. The type of Kawasaki Rose 1/5
fold (valley or mountain) is unimportant at this point Designer: Toshikazu Kawasaki
in folding Diagrammed By: Winson Chan
Revision: 2.1 Date: 4/29/96
Fold along
this mountain
9 12
crease when
done
1/3
2/3
Make the following mountain and valley folds.
Make the following mountain and They are at 45 degrees relative to the grid. The
valley folds. See enlargement. Notice square in the centre can be used as a guide.
the position of the horizontal crease. When these creases are complete, mountain fold
Repeat on all four sides along the crease indicated, the entire length of the
paper
10
13
Form the two
valley folds
indicated
14
The paper should look like this after
completing each set. Renforce each Mountain fold the
set of folds by crimping along the top point behind.
darkened line. Notice the location
11 of the light gray
area over the next
three steps.
Kawasaki Rose 2/5
This is what one of the crimps looks Designer: Toshikazu Kawasaki
like. Repeat on all four sets. Diagrammed By: Winson Chan
Revision: 2.1 Date: 4/29/96
Twist fold along the lines
15 17 indicated. The next 2
steps provide a simple
method of doing a twist
fold if you are not fimiliar
with it.
Form a (slightly
modified) waterbomb
Open up the model by inserting a finger 18 base along existing
into the section indicated. Model will not creases. Fold both
remain flat. Notice the movement of the layers of paper on each
light gray section edge as indicated, while
you spread out/ flatten
the paper. Carefully
squash the paper in the
centre into a square.
16
Valley Mountain
The model after the twist
19 fold. Flip paper over.
Unfold model to step 12.
Kawasaki Rose 3/5
Designer: Toshikazu Kawasaki
Diagrammed By: Winson Chan
Revision: 2.1 Date: 4/29/96
20 flap 23
diagonal line
Re-form the crips in step 11. Turn the model upside down.
Notice the enlargement of the indicated area in the next
step. The next few steps will consist of re-forming the
Bring together the flaps formed by the twist fold. Valley folds in steps 13 to 16. This will lock the base of the rose.
fold along the diagonal line to help with this. Model will
not remain flat, and should resemble a cylinder. Make
sure that the centre points up, not down.
24
21
Enlargement of the indicated area in the previous step. No
new creases are needed. All creases were folded in correct
direction (mountain or valley) in steps 13 to 16. Make sure
to fold both layers of paper. The folder should realize this
fold is essentially a reverse fold. A review of a reverse fold
is found on page 5.
To create the cylinder like appearence of the model, place
one hand around the model, insert one finger(of the other
hand) and rotate finger clockwise. Be careful not to make
break the paper. The model will wrap tightly around your 25
finger. This step will improve the look of the model and is
not essential.
22
This is what the model looks like. Notice the darkened
line, and compare it with the diagram in step 22.
Repeat this with all 4 flaps.
Kawasaki Rose 4/5
View from the bottom of the rose before the. reverse
Designer: Toshikazu Kawasaki
folds. Notice the movement of the darken line. See
step 25. Diagrammed By: Winson Chan
Revision: 2.1 Date: 4/29/96
26 28
The underside of the completed rose. The rose is now
essentially done. Flip the rose over, reform the centre
by inserting a finger and rotating it clockwise as in step
XX. Form petals into desired shape. The rose is now
This is what the model looks like after the inside reverse complete
fold on each flap. It is essential that the hole in the centre
is as small as possible. Try pulling on the flaps to reduce
the side if the hole. Next, do a outside reverse fold(on the
two layers) so that is wraps back around the model.
27 29
A very poor drawing of the top of the rose. I'll fix it in
my next revision!
Have Fun!
This is what the model looks like after one outside reverse
fold. Notice how we have now refolded steps 13 to
16.Now do the same on the remaining 3 flaps so that the
four flaps overlap each other. The last fold is the most
difficult.
The Kawasaki Rose was taught to me ( the diagrammer)
by Joseph Wu, who was taught by Toshikazu Kawasaki
Inside Reverse Fold at the Convention in New York in 1994.
You can make copies of these diagrams for
personal use and for friends, but do not make
large number of copies for wide distribution
(i.e. at a Convention).© 1996
Outside Reverse Fold
Kawasaki Rose 5/5
Designer: Toshikazu Kawasaki
Diagrammed By: Winson Chan
Revision: 2.1 Date: 4/29/96