Nghệ thuật xếp hình Nhật Bản: RHINO
Nghệ thuật xếp hình Nhật bản: RHINO. Tài liệu rất có ích, nó giúp bạn nâng cao kỹ năng gấp tất cả mọi thứ bằng giấy. Bạn có thể gấp thành thạo những gì bạn thích cho riêng mình và cho bạn bè bạn.
Black Rhinoceros c Ronald Koh - 1993
1. 2.
A sheet of paper of at least 20 cm square Now fold the lower diagonal edges to meet
would be preferred for this model. Fold and along the vertical crease line in the centre.
unfold diagonally in half, creasing well.
3. 4.
5.
Turn paper over ... ... and fold down the Turn the paper over
triangular portion at the again ...
top as illustrated.
6. 7.
... and unfold the overlapping layer to ... like this. Now fold vertically in half,
each side ... from left to right ...
8. 9. 10.
... then valley fold along the Separate the two layers Fold and unfold,
edge of the white triangular along the horizontal edge Creasing firmly ...
portion, crease firmly, and and squash fold.
unfold.
11. 12. 13.
Do a petal fold by pulling the ... like this. Turn the ... separate the two layers
diagonal edge of the paper over, ... along the diagonal
uppermost layer 45 degrees edges on the left and
down and to the left, while squash fold.
drawing in the horizontal and 15.
vertical edges at the top 16.
together ...
14.
Valley fold the horizontal edge ... then fold done the Fold down both corners at
of the white layer to meet the coloured triangular the top, and do a rabbit's
diagonal edge of the coloured portion in the middle ear fold at the bottom ...
layer on each side, ... as illustrated.
17.
18.
... like this. Separate the two
layers of the triangular tab
and squash fold, ...
... then mountain fold along the existing
diagonal crease lines to narrow the
upper section before bringing the point
at the top to meet the point at the
bottom ...
19. 20. 21.
... like this.
Fold the lower diagonal edges to Fold and unfold again as
meet the adjacent diagonal edge illustrated, creasing firmly again.
of the kite-shaped flap in the
centre, crease firmly, and unfold.
22.
23.
24.
Fold the first layer up,...
... then turn the model over.
25.
Grasp each side at the circled
areas, holding the coloured
portions only, then pull apart to
open out ...
26.
... like this. Now lift up the
the white triangular layer
at the top and the second
layer at the bottom ...
27.
... then collapse along the existing crease
lines with mountain and valley folds as
illustrated ...
... like this ...
28. 29. 30.
Valley fold the triangular
tabs in the middle
upwards, at the same
time valley folding the
Draw one layer to the left and ... as illustrated, then fold and lower diagonal edges to
squash fold ... unfold, creasing firmly. meet in the centre ...
32. 33.
31.
... like this. Fold down the
triangular tabs in the
middle again.
Swivel one layer on the Fold and unfold, creasing
right to the left. firmly, ...
34. 35.
... then reverse fold along the ... like so. Fold and unfold, creasing
crease lines made in Step 33 firmly again, ...
...
36. 37.
... then mountain fold the excess Rabbit's ear fold as shown,
paper under along the crease line swivelling one layer on the left
made in Step 35. to the right.
38. 39. 40.
Swivel one layer on Turn model Separate the two
the left to the right, and over. layers along the
repeat from Step 33 on diagonal edges
this side. and squash fold, ...
41. 42. 43. 44.
... then narrow as
illustrated ...
45.
... like this. Reverse fold the Fold the flap ... and crimp with a
corners along the down again ... mountain and
existing crease lines and valley fold, ...
bring the resulting point
at the bottom all the way
to the top.
... like this.
46. 47. 48.
49.
Fold down one layer ... then fold up Turn the model
from the top ... again, making a over.
little crimp.
50. Fold down the first
layer at the apex of
51. the model and crease
well, then reverse fold
the points on each side.
Fold up the the first layer at
the apex again, and valley
fold the lower points Valley fold the lower
upwards at the illustrated points down again.
angles and proportions.
52. 53 54. 55.
Unfold the Steps ... and refold along ... like this.
at 49 and 50 on the crease lines
the apex of the as illustrated, ... 56.
model ...
57.
Make a crimp as illustrated
with a mountain and valley
fold, ...
... then mountain fold
the model vertically
in half.
Grasp the head firmly and
pull down gently ... 59. 60.
58.
Rabbit's ear fold the triangular Outside reverse fold the
tabs on each side to form the next point to form the
ears, then flatten the head second horn, and valley
temporarily and outside fold the little corner on
reverse fold the short point in each side to form the eyes.
the middle to form one horn.
Broaden each hind leg by
drawing out the second layer 61.
to the back as indicated by 62.
the dotted lines.
63.
Sink the front section
of the horn. A pair of
64. Crimp fold the front tweezers will help.
of the remaining Open out both ears as
... then lift up the point under ... shown.
first layer on each
side ...
... like this. 65.
66.
Inside reverse fold all the legs and the
Narrow both sides of the forelegs base of the tail as illustrated.
by fold the excess paper within.
Do another reverser fold at the tip
of the tail, then complete the model
by rounding off the back.